The truss rod is a thin, strong metal rod that runs along the inside of the neck. It is used to correct changes to the neck's curvature caused by aging of the neck timbers, changes in humidity, or to compensate for changes in the tension of strings. The tension of the rod and neck assembly is adjusted by a hex nut or an allen-key bolt on the rod, usually located either at the headstock, sometimes under a cover, or just inside the body of the guitar underneath the fretboard and accessible through the sound hole. Some truss rods can only be accessed by removing the neck. The truss rod counteracts the immense amount of tension the strings place on the neck, bringing the neck back to a straighter position. Turning the truss rod clockwise tightens it, counteracting the tension of the strings and straightening the neck or creating a backward bow. Turning the truss rod counter-clockwise loosens it, allowing string tension to act on the neck and creating a forward bow.
As a general rule, brass strings are always going to be brighter than bronze strings. Though, counterintuitively, many brass strings go by the moniker of “80/20” bronze. These strings are actually the one in the same. Brass, or 80/20 bronze as it’s often known, is made from 80% copper and 20% zinc. This gives the strings a bright and cutting voice, though when used on guitars that already have a prominent high-end response it can make an instrument sound thin and tinny. For best results, use brass strings on a guitar that’s an OM size or larger (so this would include OM guitars, dreadnoughts, and jumbos).
Unlike a piano or the voices of a choir, the guitar (in standard tuning) has difficulty playing the chords as stacks of thirds, which would require the left hand to span too many frets,[40] particularly for dominant seventh chords, as explained below. If in a particular tuning chords cannot be played in closed position, then they often can be played in open position; similarly, if in a particular tuning chords cannot be played in root position, they can often be played in inverted positions. A chord is inverted when the bass note is not the root note. Additional chords can be generated with drop-2 (or drop-3) voicing, which are discussed for standard tuning's implementation of dominant seventh chords (below).

Anyone playing and/or teaching guitar needs staff paper, blank tab, guitar chord charts, guitar scale charts, and fretboard diagrams to chart their guitar lessons and musical ideas. You can find books with some combination of these blank charts and grids, but you can’t find one with all of them organized in a practical way. That’s why we chose to design our own.

By now, you’ve already decided whether to stick with the Guitar or to drop it. If you’re one of the lucky few that stuck with it, in spite of having an extremely busy schedule with work and family obligations, congratulations. Contrary to popular belief, taking the time out for routine Guitar practice has tremendous benefits, even for the busiest of people.
When playing seventh chords, guitarists often play only subset of notes from the chord. The fifth is often omitted. When a guitar is accompanied by a bass, the guitarist may omit the bass note from a chord. As discussed earlier, the third of a triad is doubled to emphasize its major or minor quality; similarly, the third of a seventh is doubled to emphasize its major or minor quality. The most frequent seventh is the dominant seventh; the minor, half-diminished, and major sevenths are also popular.[79]

Chords are the backbone of most guitar music. As a beginner, mastering the most common chords allows you to play along to popular songs and even start writing your own. Technically speaking, a chord is a group of three or more notes played in one smooth strumming motion. Chords are classified according to the overall effect they produce. Major and minor chords, which create happy and sad sounds, respectively, are the most basic chords you'll need to play beginner-friendly songs.

Kyser®'s nickel-plated electric guitar strings give you a warm, rich, full sound. They are precision wound around a carefully drawn hex shaped carbon steel core. The outer nickel-plated wrap maintains constant contact with the hex core resulting in a string that vibrates evenly for maximum sustain, smooth sound, and allows easy bending. Click the individual string images to view more gauge information.
Let’s be honest, private lessons aren’t the best idea for college students who are generally tight on budget, time, and commitments. However, that doesn’t mean you should stop learning and practicing. You can still work on the guitar by taking classes or participating in music programs at your college. These tend to be more affordable, more social, and less stressful than trying to fit private lessons into your routine.
We believe that music is a social activity so we present students with numerous opportunities to interact with each other. Each year we hold multiple recitals which offer a low-pressure opportunity to perform in front of an audience with other like-minded music students.  In addition to recitals, students frequently go out into the community to perform outreach concerts at local hospitals, schools, and nursing homes. Students also have the option to join group classes at our Santa Clara location. This offers students a chance to perform for each other more frequently, as well as join on our many performance ensembles. 
Students can earn a Certificate in MI’s Performance Studies program for Guitar. With an innovative 360-degree approach to music education, MI Certificates are centered on Harmony, Theory and Ear Training, with core subjects in Reading, Technique and Performance. This Certificate program provides students with a broad foundation of knowledge and practical experience, encouraging the rapid development of skills in preparation for a range of professional music performance situations.