We've carefully selected the most qualified and well-respected instructors—a great fit for those who are just learning to play as well as those who want to advance their skill and become master musicians. Beyond having celebrated careers, every instructor is personable, patient and well educated, often with advanced degrees in music from renowned schools of music. For added peace of mind, all of our instructors are required to pass a thorough background check.
There are separate chord-forms for chords having their root note on the third, fourth, fifth, and sixth strings. For a six-string guitar in standard tuning, it may be necessary to drop or omit one or more tones from the chord; this is typically the root or fifth. The layout of notes on the fretboard in standard tuning often forces guitarists to permute the tonal order of notes in a chord.
Play the A Major. This is another "big chord," sonically. There are several ways to play this. You can use one finger across the 2nd fret of the B, G, and D strings (playing C#, A, and E, respectively), or any other combination of fingers. For this example, we'll use the 4th finger on the B string, 3rd finger on the G string, and 2nd finger on the D string.
Guitar Chords are a group of at least 3 notes played together, this means three different notes, i.e. notes with 3 different pitches. If, for example, you select an E major chord on the guitar chord generator on this page, you can see the 3 notes E, B and G# (Ab) make up this chord. Some notes can be expressed as either sharp or flat (enharmonic spelling), the notes sound just the same but the naming of them is decided by which key the song is in. You can find out more about this in our music theory section.
Traditional electromagnetic pickups are either single-coil or double-coil. Single-coil pickups are susceptible to noise induced by stray electromagnetic fields, usually mains-frequency (60 or 50 hertz) hum. The introduction of the double-coil humbucker in the mid-1950s solved this problem through the use of two coils, one of which is wired in opposite polarity to cancel or "buck" stray fields.
A capo (short for capotasto) is used to change the pitch of open strings. Capos are clipped onto the fretboard with the aid of spring tension, or in some models, elastic tension. To raise the guitar's pitch by one semitone, the player would clip the capo onto the fretboard just below the first fret. Its use allows players to play in different keys without having to change the chord formations they use. For example, if a folk guitar player wanted to play a song in the key of B Major, they could put a capo on the second fret of the instrument, and then play the song as if it were in the key of A Major, but with the capo the instrument would make the sounds of B Major. This is because with the capo barring the entire second fret, open chords would all sound two semitones (aka one tone) higher in pitch. For example, if a guitarist played an open A Major chord (a very common open chord), it would sound like a B Major chord. All of the other open chords would be similarly modified in pitch. Because of the ease with which they allow guitar players to change keys, they are sometimes referred to with pejorative names, such as "cheaters" or the "hillbilly crutch". Despite this negative viewpoint, another benefit of the capo is that it enables guitarists to obtain the ringing, resonant sound of the common keys (C, G, A, etc.) in "harder" and less-commonly used keys. Classical performers are known to use them to enable modern instruments to match the pitch of historical instruments such as the Renaissance music lute.
Almost all guitars have frets, which are metal strips (usually nickel alloy or stainless steel) embedded along the fretboard and located at exact points that divide the scale length in accordance with a specific mathematical formula. The exceptions include fretless bass guitars and very rare fretless guitars. Pressing a string against a fret determines the strings' vibrating length and therefore its resultant pitch. The pitch of each consecutive fret is defined at a half-step interval on the chromatic scale. Standard classical guitars have 19 frets and electric guitars between 21 and 24 frets, although guitars have been made with as many as 27 frets. Frets are laid out to accomplish an equal tempered division of the octave. Each set of twelve frets represents an octave. The twelfth fret divides the scale length exactly into two halves, and the 24th fret position divides one of those halves in half again.
Left-handed players sometimes choose an opposite-handed (mirror) instrument, although some play in a standard-handed manner, others play a standard-handed guitar reversed, and still others (for example Jimi Hendrix) played a standard-handed guitar strung in reverse. This last configuration differs from a true opposite handed guitar in that the saddle is normally angled in such a way that the bass strings are slightly longer than the treble strings to improve intonation. Reversing the strings, therefore, reverses the relative orientation of the saddle, adversely affecting intonation, although in Hendrix's case, this is believed to have been an important element in his unique sound.
This unique degree program combines contemporary music performance training with the rigorous study of traditional disciplines including sight-reading, music history, arranging, conducting, recording and more. The comprehensive program instructs students to demonstrate stylistic depth, creative maturity and professional competence in preparation for careers in today’s music industry.