Bolt-on necks, though they are historically associated with cheaper instruments, do offer greater flexibility in the guitar's set-up, and allow easier access for neck joint maintenance and repairs. Another type of neck, only available for solid body electric guitars, is the neck-through-body construction. These are designed so that everything from the machine heads down to the bridge are located on the same piece of wood. The sides (also known as wings) of the guitar are then glued to this central piece. Some luthiers prefer this method of construction as they claim it allows better sustain of each note. Some instruments may not have a neck joint at all, having the neck and sides built as one piece and the body built around it.
The Beatles668 tabs 637 visualizations1 Elvis Presley542 tabs 410 visualizations2 Nirvana513 tabs 360 visualizations3 Eagles139 tabs 349 visualizations4 Frank Sinatra387 tabs 348 visualizations5 Misc Soundtrack1160 tabs 279 visualizations6 Misc Cartoons897 tabs 265 visualizations7 Green Day650 tabs 254 visualizations8 Metallica382 tabs 247 visualizations9 Johnny Cash441 tabs 221 visualizations10
To play a C chord on a guitar, put your ring finger on the third fret on the A string, your middle finger on the second fret on the D string, leave the G string open, and put your index finger on the first fret of the B string. Before you try to strum the chord, play each note individually until the note sounds clear. When you've mastered the C chord, try moving on to other chords like G or F.
While Courses are a great way to learn guitar on your own, sometimes you need personalized feedback or private lessons from top guitar instructors in order to bust out of that rut or step your guitar playing up to the next level. With no pressure nor scheduling issues, TrueFire Online Classrooms are the best way to take private guitar lessons online!

At least two instruments called "guitars" were in use in Spain by 1200: the guitarra latina (Latin guitar) and the so-called guitarra morisca (Moorish guitar). The guitarra morisca had a rounded back, wide fingerboard, and several sound holes. The guitarra Latina had a single sound hole and a narrower neck. By the 14th century the qualifiers "moresca" or "morisca" and "latina" had been dropped, and these two cordophones were simply referred to as guitars.[8]
The black dots found on the chord diagrams tell you which fret to press down, and on which string and with which numbered finger. Additionally, you will sometimes see circles above the nut. These circles tell you to play that open string without pressing any fret. So using what we know so far about strings, finger numbers, and dots, let’s check out that same chord diagram again:
The guitar is a fretted musical instrument that usually has six strings.[1] It is typically played with both hands by strumming or plucking the strings with either a guitar pick or the finger(s)/fingernails of one hand, while simultaneously fretting (pressing the strings against the frets) with the fingers of the other hand. The sound of the vibrating strings is projected either acoustically, by means of the hollow chamber of the guitar (for an acoustic guitar), or through an electrical amplifier and a speaker.
The top, back and ribs of an acoustic guitar body are very thin (1–2 mm), so a flexible piece of wood called lining is glued into the corners where the rib meets the top and back. This interior reinforcement provides 5 to 20 mm of solid gluing area for these corner joints. Solid linings are often used in classical guitars, while kerfed lining is most often found in steel string acoustics. Kerfed lining is also called kerfing because it is scored, or "kerfed"(incompletely sawn through), to allow it to bend with the shape of the rib). During final construction, a small section of the outside corners is carved or routed out and filled with binding material on the outside corners and decorative strips of material next to the binding, which are called purfling. This binding serves to seal off the end grain of the top and back. Purfling can also appear on the back of an acoustic guitar, marking the edge joints of the two or three sections of the back. Binding and purfling materials are generally made of either wood or plastic.
When you get right down to it, Guitar Center's friendly instructors will do everything they can to help you reach your highest level of musical potential. And remember, guitar lessons are available for both newcomers to the instrument, as well as experienced players who want to push the limits of their performance to even greater heights. If you would like to learn more about any upcoming workshops at a Guitar Center near you, feel free to give us a shout via phone or email. Any info you need can be found on our Guitar Center Lessons homepage and we'll gladly answer any questions you may have.
With that being said, nickel strings definitely have a richer tone with more body than steel strings. This warmth is especially pleasing when used to play older genres of music, blues in particular. The strings are also a great fit for rhythm work, because the warmth inherent to these strings helps to increase the overall body and richness of a mix.
The Master of Music in Performance (Guitar) from Musicians Institute combines advanced performance training with additional study in both traditional and contemporary disciplines such as music history, theory, education, research skills, recording technology, production, business relations and online brand management, taking your guitar skills to the highest level.
×