The ratio of the spacing of two consecutive frets is {\displaystyle {\sqrt[{12}]{2}}} (twelfth root of two). In practice, luthiers determine fret positions using the constant 17.817—an approximation to 1/(1-1/ {\displaystyle {\sqrt[{12}]{2}}} ). If the nth fret is a distance x from the bridge, then the distance from the (n+1)th fret to the bridge is x-(x/17.817).[15] Frets are available in several different gauges and can be fitted according to player preference. Among these are "jumbo" frets, which have much thicker gauge, allowing for use of a slight vibrato technique from pushing the string down harder and softer. "Scalloped" fretboards, where the wood of the fretboard itself is "scooped out" between the frets, allow a dramatic vibrato effect. Fine frets, much flatter, allow a very low string-action, but require that other conditions, such as curvature of the neck, be well-maintained to prevent buzz.
Ive been playing guitar for about 3 years, and this is the best song book I have ever learned from. Songs range from sweet home alabama by lynard skynard all the way to raining blood by slayer. All of the songs are accurate and complete with notes, tabs, lyrics, and copyright info. If you are like me, and you prefer to learn songs the way they were meant to be played than this book is for you.

I've given this guitar chord book away as a gift and purchased one for myself. I love the spiral bound binding and I'm sure all but the best guitar players will not run out of chords to learn in this little book. I highly recommend this book to learn guitar chords. It's not a book that teaches you how to play a guitar. It is mostly chords but this is a crucial part of learning to play, right?
Electric guitars can have solid, semi-hollow, or hollow bodies; solid bodies produce little sound without amplification. Electromagnetic pickups convert the vibration of the steel strings into signals, which are fed to an amplifier through a patch cable or radio transmitter. The sound is frequently modified by other electronic devices (effects units) or the natural distortion of valves (vacuum tubes) or the pre-amp in the amplifier. There are two main types of magnetic pickups, single- and double-coil (or humbucker), each of which can be passive or active. The electric guitar is used extensively in jazz, blues, R & B, and rock and roll. The first successful magnetic pickup for a guitar was invented by George Beauchamp, and incorporated into the 1931 Ro-Pat-In (later Rickenbacker) "Frying Pan" lap steel; other manufacturers, notably Gibson, soon began to install pickups in archtop models. After World War II the completely solid-body electric was popularized by Gibson in collaboration with Les Paul, and independently by Leo Fender of Fender Music. The lower fretboard action (the height of the strings from the fingerboard), lighter (thinner) strings, and its electrical amplification lend the electric guitar to techniques less frequently used on acoustic guitars. These include tapping, extensive use of legato through pull-offs and hammer-ons (also known as slurs), pinch harmonics, volume swells, and use of a tremolo arm or effects pedals.
On guitars that have them, these components and the wires that connect them allow the player to control some aspects of the sound like volume or tone using knobs, switches, or buttons. The most basic electronic control is a volume knob. Some guitars also have a tone-control knob, and some guitars with multiple pickups have pickup selector switches or knobs to determine which pickup(s) are activated. At their simplest, these consist of passive components, such as potentiometers and capacitors, but may also include specialized integrated circuits or other active components requiring batteries for power, for preamplification and signal processing, or even for electronic tuning. In many cases, the electronics have some sort of shielding to prevent pickup of external interference and noise.
Inlays are visual elements set into the exterior surface of a guitar, both for decoration and artistic purposes and, in the case of the markings on the 3rd, 5th, 7th and 12th fret (and in higher octaves), to provide guidance to the performer about the location of frets on the instrument. The typical locations for inlay are on the fretboard, headstock, and on acoustic guitars around the soundhole, known as the rosette. Inlays range from simple plastic dots on the fretboard to intricate works of art covering the entire exterior surface of a guitar (front and back). Some guitar players have used LEDs in the fretboard to produce unique lighting effects onstage. Fretboard inlays are most commonly shaped like dots, diamond shapes, parallelograms, or large blocks in between the frets.
First, being able to learn directly from amazing artists like Paul Gilbert is incredible. He's a great teacher and has a way of explaining things that are easy to understand and replicate. The video format is also extraordinarily helpful; I've used other sites that use only written materials (usually .pdf format), and they are difficult to navigate. The feedback, though, is what really makes this website head and shoulders above the others (even the other video websites). When I record myself and send it in, I get a response from Paul that critiques in an incredibly constructive way as well as additional exercises to work at really honing that skill. In addition, getting to see what tips he gave to other users is awesome! If you want to learn an instrument, there's no better way.
The intensive A.A. curriculum prepares musicians to perform in any professional situation, along with learning professional development skills such as basic computer use, EPK creation, resume and bio writing, and social media as a tool for business and networking. The Associate of Arts Degree is intended to equip students with the knowledge and training needed to become professional performers in today’s music industry.
×